1 Jun ASTM D(). Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading. ASTM D Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading. Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading. Theory: ASTM D is used to determine.
|Published (Last):||11 June 2010|
|PDF File Size:||17.36 Mb|
|ePub File Size:||17.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
The length of the plate should equal or exceed that of the specimen.
This is a function of the pipe dimensions and the physical properties of the material of which the pipe is made. The platen has a spherically seated joint that wobbles slightly and lines up the v2412 force on the pipe specimen.
Planar Biaxial Testing Guide.
The eP2 Digital Controller, a standalone touch panel unit, offers a balance between performance and simplicity. Contact our Engineers Today!
ADMET testing controllers are capable of automatically performing and reporting these calculations at any given deflection.
A spherically seated compression platen can be used in order asmt normalize the vector of compression. While this test method can be used in measuring the pipe stiffness of corrugated plastic pipe or tubing, special conditions and procedures are used.
ASTM D is a testing standard used to determine the stiffness and load deflection of plastic pipe.
How to Build a New Test. Depending on the type of plastic pipe being tested, cut the specimen to the lengths specified. Prepare and test at least three specimens for each pipe.
Condition the specimens to the temperature detailed in the specification. Load measurements are taken at constant intervals. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Care must be taken to account for the mid-section of the pipe which will expand slightly as the pipe is compressed. A compression cage can be use for tension only testing machines in order to convert the tensile force into a compressive force.
ASTM D Plastic Pipe Deflection Testing – ADMET
ASTM D is used to determine pipe stiffness and to characterize the material behavior of d242 in pipe form. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the test method.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Pipes tested under ASTM D must be smaller than the envelope of the two compression platens by at least a half an inch. Calculations for ASTM D include percentage load deflection, pipe stiffness, and the stiffness factor.
Calculate pipe stiffness, stiffness factor, and percentage pipe deflection using the formulas provided in the speciation. ADMET testing controllers sati sfy this requirement and can automatically record load and deflection. Record the load and deflection when these events are observed. Be sure to cut asrm pipe cleanly. These details are included in the product standards, for example, Specification F Be aware of line cracking, wall cracking, wall delamination, and break.
Wide versions of all of these machines are available to accomodate large pipe diameters. This summary is intended to help you understand the axtm procedure and equipment required to complete this test with accuracy.
We’re ready to help! Square or circular platens can be used, with most customers choosing a square platen.
ASTM D2412 Plastic Pipe Deflection Testing
Measure the length, d22412 diameter, and average wall thickness of the specimen. Historical Version s – view previous versions of standard. Automotive Interior Mechanical Testing Guide. Compression platens are used for D A pair of smooth compression platens capable of applying the required load without bending. Sales Support Calibration Calculators.
The values given in parentheses are mathematical conversions to SI units that are provided for information only asgm are not considered standard. Link to Active This link will always route to the current Active version of the standard.
The pipe is compressed between two platens in order to gather load-deflection data.
Plate width should equal or exceed the pipes contact area at maximum deflection plus 6 in. Stop the test at break, when the load no asym increases with deflection or when the specimen reaches the required maximum deflection.
Begin compressing the specimen at the specified rate.